Mountain Trail Campers
Australian Wheel Clamp
Fitting Instructions

Published by William Flynn
on November 28, 2017

Australian made highest security rated Wheel Clamp

How the High Tensile Chain fits round the back of the vehicle's Wheel.

The included 10mm diameter High Tensile Chain cannot be cut
with a Bolt Cutter no matter how long the Bolt Cutter is.

Australian Manufacturer Direct Special Offer

Wednesday November 14, 2018 between 10.30am to 9.30pm

Scroll down this page to read how much you will save.

Note: The Australian made Wheel Clamp has many names depending what it is being sold to secure eg. Australian Wheel Clamp, Caravan Wheel Clamp, Camper Trailer Wheel Clamp, Boat Trailer Wheel Clamp, Trailer Wheel Clamp and others.

Included in this page...

1. Two methods to fit the Australian made Wheel Clamp security option Supreme to one of the Mountain Trail Camper wheels.
2. How to fit the Australian Wheel Clamp security option Supreme to an Mountain Trail Camper Wheel using fitting method one.

1: Two methods to fit the Australian made Wheel Clamp security option Supreme to one of the Mountain Trail Camper wheels.

There are two methods to fit the Australian made Wheel Clamp depending on the Vehicle type. The following list is a guide to indicate whether you use fitting method one or two.

1. Fitting Method One for all towable or drivable vehicles listed below plus any other type of towable Vehicle not listed.
2. Fitting Method Two used for the vehicles listed below.

Choose the correct fitting method from the above list of vehicles then download the instructions, in PDF format, from the following list.

2: How to fit the Australian Wheel Clamp security option Supreme to an Mountain Trail Camper Wheel using fitting method one.

Step 1

Stand the Steel Shield in front of the Wheel.

Step 2

Place the Chain through the two bottom holes in the Steel Shield.

NB: Step 2 - We suggest to save you a few seconds while fitting the Australian Wheel Clamp security option Supreme place a piece of coloured tape or twist a short piece of wire, as seen in the pictures, or similar around the middle link in the length of Chain. This will enable you to quickly centralize the Chain in the center of the Steel Shield.

On the left side pass the Chain under then over the vehicle's leaf springs or tubular frame (as used to make most Caravan chassis) then through the top hole.

Step 4

Repeat the same procedure on the right side as per Step 3.

Note...

If your towable or drivable Vehicle has coil springs and/or piston suspension, seen in the following picture, steps 1 and 2 are the same but as there are no leaf springs, seen in the pictures in steps 3 and 4 above, instead you wrap the Chain round any part of the chassis.

Steps 5 and 6 are the same no mater leaf springs or coil springs and/or piston suspension.

Step 5

Grip both ends of the Chain and pull to make the Chain taut.

Step 6

Locking the Australian Wheel Clamp security option Supreme with the patented Padlock Protection Steel Shroud and customised Padlock - opens in a new window, it will only take a few times to get the hang of it.

1st: Place both ends of the Chain in the slot on each side of the Steel Shroud.

2nd: Place the removable Shackle in the holes at the top of the Steel Shroud.

3rd: Hold the Steel Shroud in your hand and place a couple of fingers over the top of the Shackle. Look at the opposite end of the Steel Shroud to make sure the Shackle is in the center then insert the Padlock Body in the hole at the bottom of the Steel Shroud. To lock the Padlock turn the key after pushing the Padlock into the Shackle.

Note: The padlock's Shackle only fits into the Padlock body one way, you have to remember the correct way, here's a couple of suggestions:

• The long side of the Shackle goes into the side of the Padlock where the ball bearing has been removed.
• Or the method I use is, on one edge of the Padlock body there is a pin hole, the short side of the padlock's Shackle goes in the side where this pin hole is.

Simple to fit to a Wheel.
Takes less than a minute to fit.

Mountain Trail Camper

Is Now Protected

I trust if you own or are thinking about purchasing an Mountain Trail Camper you seriously consider purchasing the Australian Wheel Clamp security option Supreme to stop it being stolen.

If you gained knowledge from reading this page
please email this page link to a friend, thank you.

Or...

Share this link
www.wheelclamp.com.au/articles-2017/mountain-trail-campers.php
on your favourite social network.

Article Archive

Australian Manufacturer Direct Special Offer

Wednesday November 14, 2018 between 10.30am to 9.30pm

save $170 or $188

Plus next business day free delivery anywhere in Australia.

Theft Proof Security Products Web Sites

Below links open in a new window.

High Security, Light-Weight
Virtually Indestructible Safe

Easy DIY Installation in:
Residential Homes, Vehicles
Caravans, Motor Homes, RV’s, Offices, Factories and Boats.

If you don't need any more information to make a decision to purchase the world's highest security rated Australian made Wheel Clamp then

Site Map

Copyright © 1994 – 2018
Speculator Holdings Pty Ltd

Last Updated
Wednesday November 14, 2018