How To Fit
Australian Wheel Clamp

fitting instructions
Australian Wheel Clamp

fits all size wheels

buy today
April 02, 2020

special offer

ends
April 09, 2020

... plus ...

FREE delivery
the next business day

guaranteed
by the Australian
manufacturer until

April 02, 2030

that’s a
10 year warranty

... plus ...

both are QUICK and simple
to fit to and remove from a wheel

Go  Vehicles the Australian Wheel Clamp will fit.

Go  Australian Wheel Clamp fitting instructions.

Go  How to fit the Enforcer.

Go  How to fit the Supreme.

Go  Special Offer - Australian manufacturer direct between April 02, 2020 ends April 09, 2020 save $$$ off RRP plus free delivery the next business day.

Go  When purchasing Australian Wheel Clamp the only decision you have to make is, choose which of the two security options you want to purchase Enforcer or Supreme.

Go  Australian Wheel Clamp guaranteed for 10 years by the Australian manufacturer.

Go  Where to purchase the Australian Wheel Clamp.

Go  If you have enough information to place your order buy now.

Go  Ultimate security combination.

Go  Other products and / or services you maybe interested in.

Go  What to do next.

Go  Site map.

some links on this page open in a new window

Vehicles the Australian Wheel Clamp will fit.

The Australian Wheel Clamp fits all size wheels without adjusting anything

This is achieved using a length of 10mm diameter High Tensile.

Australian Wheel Clamp fitting instructions.

Fitting time...

The first time you fit the Australian Wheel Clamp it will take you about five minutes.

The second time about 3 - 4 minutes.

After your fifth time you should fit the

Removing time...

Takes about 15 seconds no mater if its the first, second or 20th time.

How to fit the Australian Wheel Clamp...

The following fitting instructions are for both security options.

There are a few methods to fit the Australian Wheel Clamp.

After you have fitted it a few times you may find another method.

As the designer and manufacturer we believe the following is the easiest and quickest method to fit the Australian Wheel Clamp.

Note...

The following instructions are based on the vehicle having leaf spring.

The same or similar method applies to a tubular frame chassis ( most caravans ) and 4wd off road camper trailers with coil springs and / or piston suspension.

important to remember

The Stainless Steel Shield DOES NOT have to be tight to the face of the wheel.

There can be up to a 50mm ( 2 inch ) gap between the Stainless Steel Shield and the face of the wheel.

How to fit the Enforcer.

The Stainless Steel Shield has four specifically positioned holes enabling the 10mm diameter High Tensile Chain to pass through.

Place the Stainless Steel Shield in front of the wheel.

Lay the chain in front of the Stainless Steel Shield.

Un-lock the padlock then put it next to the chain.

Put the left end of the chain through the left bottom hole, under then over the top of the leaf springs then through the top left hole in the Stainless Steel Shield.

With your right hand pick up the padlock then place the shackle through the third chain link.

Why...

The shackle will stop the chain falling out of the top left hole.

For quicker fitting...

Pull the chain back so there are only three links below the top left hole.

Then pull any excess chain back to the bottom of the Stainless Steel Shield.

Repeat the same on the right side, accept the bit about the shackle.

After you have put the chain through the top right hole make sure the chain is as tight as possible against the wheel.

Note...

You will have more than three chain links below the top right hole.

Locking the Enforcer Wheel Clamp...

With one hand hold both sides of the chain, with the other hand remove the padlock from the chain on the left side then put the padlock through both sides of the chain as close to the underside of the two top holes.

Why...

To keep the chain as tight as possible against the Stainless Steel Steel and the wheel.

Finally...

Lock the padlock with the key.

is now secure

How to fit the Supreme.

The Supreme includes our patented locking system.

Below explains how to lock the padlock and with the Steel Shroud although we recommend you lock the padlock and chain a few times before you use it to lock the Australian Wheel Clamp.

Important...

There is no standard method used by the numerous manufacturers who manufacture chassis that have coil springs and / or piston suspension.

Therefore I cannot state how to fit the security option Supreme Australian Wheel Clamp to your off road vehicle as I have above for the security option Enforcer.

All I can do is explain how to fit the Supreme to a vehicle that has coil springs and / or piston suspension then you need to figure out how to fit the Supreme to your off road vehicle.

The Stainless Steel Shield has four specifically positioned holes enabling the 10mm diameter High Tensile Chain to pass through.

Place the Stainless Steel Shield in front of the wheel.

Lay the chain in front of the Stainless Steel Shield.

Un-lock the padlock, remove the shackle then put them and the Steel Shroud next to the chain.

This is the bit you have to figure out...

Put the left end of the chain through the left bottom hole then under, around and over the top of some part of the chassis then through the top left hole in the Stainless Steel Shield.

With your right hand pick up the padlock's shackle then place the shackle through the third chain link.

Why...

The shackle will stop the chain falling out of the top left hole.

For quicker fitting...

Pull the chain back so there are only three links below the top left hole.

Then pull any excess chain back to the bottom of the Stainless Steel Shield.

Repeat the same on the right side, accept the bit about the shackle.

After you have put the chain through the top right hole make sure the chain is as tight as possible against the wheel.

Note...

You will have more than three chain links below the top right hole.

How to lock the Supreme...

Pick up the Steel Shroud.

On the left side of the Steel Shield remove the padlock's shackle from the chain link.

Put the chain link in the horizontal slot in the Steel Shroud.

Then put the long side of the padlock's shackle through the top hole in the Steel Shroud and the chain.

On the right side of the Steel Shroud position the chain in the slot as close to the underside of the two top holes.

Why...

To keep the chain as tight as possible against the Stainless Steel Steel and the wheel.

Lift the shackle so its just above the chain on the right side then push the chain all the way into the Steel Shroud.

Then push the shackle into the Steel Shroud, the shackle should now be level with the top of the Steel Shroud.

Locking the padlock inside the Steel Shroud...

Hold one hand over the top of the Steel Shroud.

Insert the padlock body inside the Steel Shroud.

Then lock the padlock with the key.

is now secure

Australian Wheel Clamp Australian manufacturer direct special offer.

When purchasing the...

Australian Wheel Clamp™ the only decision you have to make is, choose which of the two security options you want to purchase Enforcer or Supreme.

buy today
April 02, 2020

ends
April 09, 2020

plus
free delivery

I don't live in Australia
email me a quotation

... or ...


... or ...

When purchasing Australian Wheel Clamp just choose the security option you want to purchase Enforcer or Supreme.

When you buy ...

Any other wheel clamp brand you first have to:

When completing the secure order form...

For the Australian Wheel Clamp you will be asked to click the radio button telling us the type of vehicle you want to protect.

That's it...

... or ...

Australian Wheel Clamp is guaranteed for 10 years by the Australian manufacturer.

The Australian made Australian Wheel Clamp will last a lifetime, if not longer, but as the manufacturer we have to be realistic with the guarantee we give our clients.

We believe a 10 year guarantee gives purchasers 100% confidence they are buying a high quality security product from a 100% Australian owned business.

buy today
April 02, 2020

the Australian manufacturer
will guarantee it until

April 02, 2027

Where to purchase the Australian Wheel Clamp.

The Australian Wheel Clamp is manufactured in Kelmscott WA.

Buy direct from us, we deliver from Kelmscott or via one of our state distribution warehouses.

If you have enough information to place your order buy now.

When purchasing the...

Australian Wheel Clamp™ the only decision you have to make is, choose which of the two security options you want to purchase Enforcer or Supreme.

... or ...


... or ...

Ultimate security combination.

Australian Wheel Clamp

STOPS
thieves stealing your vehicle

Plus...

Install the Australian made Caravan Safe Docking Station in your caravan, camper trailer or motor home, slide in and lock the Caravan Safe to protect your valuables while you are on holiday.

Then when you come home...

Remove the Caravan Safe from its Docking Station in your caravan, camper trailer or motor home, take the Caravan Safe inside your house or apartment, slide it into the installed Docking Station, lock it, now its a Home Safe to secure cash, credit cards, jewelery, insurance documents, your will, backed up computer data or any small valuables that will fit.

Other Australian made wheel clamp sites...

Camper Trailer Security Wheel Clamp

Caravan Wheel Clamp

Boat Trailer Wheel Clamp

Other products and / or services you maybe interested in.

if you have enough information
to place your order

buy today
April 02, 2020

special offer

ends
April 09, 2020

... plus ...
free delivery
the next business day

I don't live in Australia
email me a quotation

... or ...

What to do next.

Site Map

Copyright © 1994 – 2020
Speculator Holdings Pty Ltd
ABN: 78 433 438 794

Last Updated
Thursday April 02, 2020